DKAE

Victron Smartsolar Mppt 75/10

$166.60

Victron Smartsolar Mppt 75/10

VICTRON SMARTSOLAR MPPT REGULATOR 12/24V 75V/10A • BUILT IN BLUETOOTH FOR EASE OF PROGRAMMING & MONITORING

SKU: SCC075010060R Categories: ,

Victron Smartsolar MPPT:
A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. SmartSolar maintains battery health, extending its life.

PWM and MPPT charge controllers are both widely used to charge batteries with solar power. The PWM controller is in essence a switch that connects a solar array to the battery. The result is that the voltage of the array will be pulled down to near that of the battery. The MPPT controller is more sophisticated (and more expensive): it will adjust its input voltage to harvest the maximum power from the solar array and then transform this power to supply the varying voltage requirement of the battery plus load. Thus, it essentially decouples the array and battery voltages so that there can be, for example, a 12 volt battery on one side of the MPPT charge controller and panels wired in series to produce 36 volts on the other.

It is generally accepted that MPPT will outperform PWM in a cold to temperate climate, while both controllers will show approximately the same performance in a subtropical to tropical climate. Besides performing the function of a basic controller, an MPPT controller also includes a DC to DC voltage converter, converting the voltage of the array to that required by the batteries, with very little loss of power.

An MPPT controller attempts to harvest power from the array near its Maximum Power Point, whilst supplying the varying voltage requirements of the battery plus load. Thus, it essentially decouples the array and battery voltages, so that there can be a 12 volt battery on one side of the MPPT charge controller and two 12 Vpanels wired in series to produce 36 volts on the other. If connected to a PV array with a substantially higher nominal voltage than the battery voltage, an MPPT controller will therefore provide charge current even at very high cell temperatures or in low irradiance conditions when a PWM controller would not help much.

As array size increases, both cabling cross sectional area and cable length will increase. The option to wire more panels in series and thereby decrease current, is a compelling reason to install an MPPT controller as soon as the array power exceeds a few hundred Watts (12 V battery), or several 100 Watts (24 V or 48 V battery)

 

Features:

Bluetooth Smart built-in: dongle not needed- The wireless solution to set-up, monitor and update the controller using Apple and Android smartphones, tablets or other devices.

VE.Direct- For a wired data connection to a Colour Control panel, PC or other devices

Ultra-fast Maximum Power Point Tracking (MPPT)- Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.

Load output- Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage (48V model: interface with a relay). Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof.

Battery Life: intelligent battery management- When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months. The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%. From that point onwards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.

Programmable battery charge algorithm- See the software section on the Victron website for details.

Programming, real-time data and history display options- Modern Apple and Android smartphones, tablets, macbooks and other devices: see the VE.Direct Bluetooth Smart dongle and the MPPT app discovery sheet for screenshots.

 

Specifications: 

SmartSolar Charge Controller MPPT 75/10 MPPT 75/15 MPPT 100/15 MPPT 100/20 MPPT 100/20 48V
Battery voltage 12/24V Auto Select 48V
Rated charge current 10A 15A 15A 20A 20A
Nominal PV power, 12V 1a,b) 145W 220W 220W 290W n. a.
Nominal PV power, 24V 1a,b) 290W 440W 440W 580W n. a.
Nominal PV power, 48V 1a,b) n. a. n. a. n. a. n. a. 1160W
Max. PV short circuit current 2) 13A 15A 15A 20A 20A
Automatic load disconnect Yes
Maximum PV open circuit voltage 75V 100V
Peak efficiency 98%
Self-consumption 12V: 25 mA 24V: 15 mA 15mA
Charge voltage ‘absorption’ 14,4V / 28,8V (adjustable) 57,6V (adj.)
Charge voltage ‘float’ 13,8V / 27,6V (adjustable) 55,2V (adj.)
Charge algorithm multi-stage adaptive
Temperature compensation -16 mV / °C resp. -32 mV / °C
Max. continuous load current 15A 20A 1A
Low voltage load disconnect 11,1V / 22,2V/44,4V or 11,8V / 23,6V/47,2V or Battery Life algorithm
Low voltage load reconnect 13,1V / 26,2V/52,4V or 14V / 28V/56V or Battery Life algorithm
Protection Battery reverse polarity (fuse) / Output short circuit / Over temperature
Operating temperature -30 to +60°C (full rated output up to 40°C)
Humidity 95%, non-condensing
Data communication port VE.Direct (see the data communication white paper on our website)
ENCLOSURE
Colour Blue (RAL 5012)
Power terminals 6 mm² / AWG10
Protection category IP43 (electronic components), IP22 (connection area)
Weight 0,5 kg 0,6 kg 0,65 kg
Dimensions (h x w x d) 100 x 113 x 40 mm 100 x 113 x 50 mm 100 x 113 x 60 mm
STANDARDS
Safety EN/IEC 62109-1, UL 1741, CSA C22.2
1a) If more PV power is connected, the controller will limit input power. 1b) The PV voltage must exceed Vbat + 5V for the controller to start.

Thereafter the minimum PV voltage is Vbat + 1V

2) A PV array with a higher short circuit current may damage the controller.

Weight 1 kg
Manufacturer

Volts

12/24

Reviews

There are no reviews yet.

Be the first to review “Victron Smartsolar Mppt 75/10”

Your email address will not be published. Required fields are marked *